MB Jetway JNF9C-2600 Intel Atom 1,6GHz

6420

Mini-ITX Mainboard met ATOM N2600 1,6 GHz Dual Core!

2x SATA3(+1xSATA2+CFAST), HDMI, 1xGbLAN,PCI, DC12V input, Mini-PCIe, COM (VGA optie)

Jetway NF9C Ultra Low Profile Mini-ITX Motherboard
Processor Atom Dual Core N2600 (1.6GHz@3.5W)
Chipset Intel NM10
Memory 1 x DDR3-800 SO-DIMM slot up to 2 GB
Graphics PowerVR SGX 545 (GMA 3600@400MHz) Integrated Graphics
Audio Realtek ALC662 5.1 Channel Audio
LAN Realtek RTL8111EVL PCI-E Gigabit Ethernet
Storage 2 x SATA3 6Gb/s ports
1 x SATA2 3Gb/s Port
1 x CFast Socket
Features - Ultra slim, low-power, thin form factor design (board z-height is 20mm)
- Embedded Long-life Series, 5 Year Availability
- ECO-design for EuP Standard
- 12 VDC jack on back panel for external power supply
- ATX12V 2 x 2 power connector for alternate internal power supply
- Support 24-bit dual channel and 18-bit single channel LVDS
- Gigabit LAN with Enhanced Surge Protection
- Dual Power Options: External 12V DC or Internal 4-pin ATX
Back Panel Connectors
1 12V DC Jack
1 HDMI (1920 x 1200 @ 60 MHz)
1 COM (RS232)
3 USB 2.0
1 RJ45 LAN (10/100/1000)
1 3.5mm Audio with S/PDIF out
Onboard I/O Connectors
1 PCI Slot
1 mini PCI-E Slot
2 Serial header (RS232)
1 Serial header (RS232/RS422/485)
2 SATA3 6Gb/s Connectors
1 SATA2 3Gb/s Connectors
2 USB Pin Headers for up to 4 additional USB 2.0 Ports
1 Parallel header
1 32-pin 24-bit dual channel LVDS1 header/inverter (CHRONTEL CH7511B chipset up to 1920 x 1200)
1 32-pin 18-bit single channel LVDS2 header/inverter (PowerVR SGX 545 chipset)
1 GPIO header
1 VGA header
1 9-pin Audio header
1 Keyboard/Mouse header
1 4-pin 12V ATX Power Connector for alternate internal power supply
1 4-pin Power out header
1 Front Panel header
3 Fan header
Power Supply for NF9C
External Power Supply – the board can be powered with a 12 V external power supply though a DC connector on the back panel. The rear 12 VDC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is 12 V and the shell is GND.
Internal Power Supply – the board can, alternatively, be powered by an internal ATX12V 2 x 2 power connector.
Based on power consumption test results, the recommended power rating is 60 W (12 V/5 A).

Caution: There is no isolation circuitry between the external 12 VDC jack and the internal 2 x 2 power connector. It is the system integrator’s responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external 12 VDC jack is covered if the internal 2 x 2 power connector is to be used.

!
 << Vorige  
NIEUW